• Home
  • Matek AP_Periph CAN-L4-BM Digital Power Monitor

Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
  • Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
  • Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
  • Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen
Matek AP_Periph CAN-L4-BM Digital Power Monitor、mySite、merchandisen

Matek AP_Periph CAN-L4-BM Digital Power Monitor

35.99
        SPECIAL OFFER

          Please select all product options

          Product was out of stock

          share
          Description
          The Matek AP_Periph CAN-L4-BM CAN Digital Power Monitor offers ultra-precise monitoring for your drone needs. It features a low-power resistant path of 200μΩ, providing high efficiency in power consumption. No calibration is required and DroneCAN protocol offers convenient current & bus voltage readouts. Enjoy precision monitoring and convenience with the AP_Periph CAN CAN-L4-BM.

          Check out all our GPS modules, and our full line of Matek products!

          Specifications

          • MCU: STM32L431xC, 256KB Flash
          • INA239 85-V, 16-Bit, High-Precision Power monitor IC With SPI Interface
          • Battery Voltage sense input: 0~85V
          • Current Sense Range: 0~204.8A
          • Load current on current sensing resistor: 150A(Continuous), 204.8A(Burst)
          • Voltage accuracy: ± 0.1%
          • Current accuracy: ± 2%
          • Interface: CAN, DroneCAN Protocol, U-ART2, spare, DFU, -ST debug, SWCLK & SWDIO
          • LED: Blue, (Fast blinking, Booting), Blue, (Slow blinking, working) Red, (3.3V indicator)
          • Power supply for CAN-L4-BM board: 4.5~5.5V @5V pad/pin
          • Power consumption: 10mA
          • Operating Temperatures: -40~85 °C
            Board Size: 30mm x 22mm x 3mm.
          • Weight: 4g
          • 3D file: CAN-L4-BM_STEP.zip
          • Firmware: ArduPilot AP_Periph  MatekL431-BattMon
          •  Update: via DroneCAN GUI Tool
          • Parameters: CAN_P1_DRIVER = 1 if attached to CAN bus1 port or CAN_P2_DRIVER = 1 if attached to CAN bus2 port, BATTx_MONITOR = 8 (DroneCAN-BatteryInfo)

          Tips

          • The big pad on the bottom side is a dead pad. No any circuit network on it.
          • Solder the positive wires as close as possible to both sides of the current sensing resistor.
          • 2 ears for mounting can be cut off if you don’t need it.
          • If the CAN wires are too long, bridge the “120R” jumper.

          Includes

          • 1x Matek AP_Periph CAN-L4-BM Digital Power Monitor
          • 1x JST-GH-4P to JST-GH-4P 20cm silicon wire

          Wiring Diagram